ObsidianWire ST 5-Way Blender Harness

4

Solderless Electronics Replacement Set

  • For ST-Style Electric Guitar
  • Replaces the rear tone pot with a blender control, which can be used to fade in either the neck or bridge pickup with certain combinations of the 5-way switch
  • Controls: Master Volume, Master Tone
  • Switch positions: 1: bridge (neck pickup switchable), 2: bridge & centre (neck pickup switchable), 3: centre, 4: centre & neck (bridge pickup switchable), 5: neck (bridge pickup switchable)
  • With the highest quality components for a significant improvement over standard electronics
  • Made in New Zealand

Scope of delivery:

  • Volume control: 1 CTS 250 kOhm, short shaft, fine grooved split shaft (24 spline for US guitars & potentiometers)
  • Volume control: 1 CTS 250 kOhm, short shaft, finely ribbed slotted shaft (24 spline for US guitars & potentiometers)
  • Blender potentiometer: 1 x CTS 250 kOhm, logarithmic, fine grooved split shaft (24 Spline for US guitars & potentiometers)
  • Thread length: 9.5 mm
  • Capacitors: 150 Series Polyester Film 0.022µF
  • Switch: CRL 5-way switch
  • Jack socket: Switchcraft 1/4" mono
Produkt dostępny od Luty 2024
Numer artykułu 580109
Jednostka sprzedaży 1 szt.
Design Normal
Resistance Value 250 kOhms
Characteristic Curve Logarithmic
Thread Length 6,4 mm
Tandem Poti No
Push/Push No
Solderless No
shaft type grooved
Type Switcher
Colour Chrome
Pokaż więcej
459 zł
Zawiera podatek VAT, nie zawiera kosztów wysyłki 49 zł
Dostępny w magazynie
Dostępny w magazynie

Produkt jest dostępny w magazynie.

Informacje dotyczące wysyłki
Szacowana dostawa pomiędzy Czwartek, 16.05. and Piątek, 17.05.
1

4 Oceny klientów

5 / 5

Aby wystawić opinię, należy się zalogować.

Informacja: Aby opinie na temat sprzętu umieszczane na naszej stronie pochodziły jedynie od osób mających styczność z danym artykułem, umożliwiamy wystawianie ocen jedynie naszym klientom.

Opinie można wystawiać po zalogowaniu się w centrum klienta, używając opcji "wystaw opinię".

wykończenie

3 Opinie

google translate de
Wystąpił błąd. Proszę spróbować później.
b
Nice and neat, aber....
bluesfather 16.04.2024
+ Endlich eine (ordentliche) Platine für die Strat statt der chaotischen Fender (Ver)drahtung. Was EMG/David Gilmore schon vor vielen Jahren lieferte.
+ Endlich Schluss mit dem Chaos der Ton Potis, Ton Poti ist jetzt Master Tone!
+ Dem nasalen Biss des Bridge Pickups kann jetzt etwas Neck/Wärme dazugemischt werden, Tele konfiguration Neck/Bridge auch oder alle
3 Pickups
± Tonepoti 2 muss wegen nun falscher Beschriftung gewechselt werden z.B in Chickenhead Göldo, KBCSA klein!

- Achtung die Konter Muttern der Potis sind in Fender Gitarren US-Größe, keine Norm (DIN).
- Die verwendeten Kabel passen oft nicht in den filigranen Solderless Block
- Die abgeklipsten Kabel der Pickups sind viel zu kurz um bis zum Block zu reichen (also doch wieder löten)
- Geklemmte Litze (Geflecht aus Drähten) fransen im solderless Block leicht aus, brechen. Die Verstärkung durch Verzinnen zu "Draht" passt nicht in Slot. Passende Drahtstärke wird nicht genannt und müsste an die Pickups gelötet werden.
Aber es war die Mühe wert!
wykończenie
1
0
Zgłoś nadużycie

Zgłoś nadużycie