On-Stage KS7365EJ

82

Keyboard stand

  • Foldable keyboard stand in Z-shape
  • For 2 keyboards
  • Exterior width: 53 to 91 cm
  • Interior width: 48 to 86 cm
  • Depth of the 1st support: 41 cm
  • Height adjustment of the 1st support: 59 to 92 cm
  • Depth of the 2nd support: 41 cm
  • Height adjustment of the 2nd support: 12 to 30 cm (measured from the 1st support)
  • Angle adjustable in 10° steps
  • Dimensions (folded up): 78 x 58 x 25 cm
  • Rubber pads for a secure hold
Myynnissä vuodesta Heinäkuu 2019
Tuotenumero 449542
Myyntierä 1 kappaletta
Keyboard Supports 2
109 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Saatavilla 5-7 viikon sisällä
Saatavilla 5-7 viikon sisällä

Tuotetta saatavilla pian varastoon ja lähetykseen.

Tietoa lähetyksestä
1

82 Asiakkaiden arviot

4.4 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Vakaus

Käsittely

Työnjälki

57 Arvostelut

S
Good quality double keyboard stand with some stability problems
Samties 10.11.2020
I use the stand in my home studio for two keyboards.

The build quality of the stand is quite good and it has a good paint job. It was easy to setup following the instructions included. The stand is somewhat heavy and the overall feel is quite sturdy. Because of the weight of the stand the box it was shipped in was slightly damaged in transit.

All adjustments are done with big knobs with screws.
It has good adjustability and allows smooth (no steps) adjustment of the main height and width. Also the upper keyboard height allows easy smooth adjustment. The tilt may be adjusted in small steps. Upper keyboard stand also have two rubber coated adjustable holders at the front end to keep the keyboard from sliding forward if the stand is tilted a lot.

However the stand seems to be somewhat back heavy. Without any keyboards the stand easily topples over backwards. Because of the Z-like form, even when loaded the center of gravity of the stand is very far back when the stand is not fully extended to the upmost position.

On the other hand the floor legs protude clearly in the front
and you tend to hit your feet into them when walking by or moving around.

In general a good quality and versatile stand with some mechanical design shortcomings.
Vakaus
Työnjälki
Käsittely
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
i
Best Wallet Friendly option!
iannsk 17.06.2024
Pretty sturdy and and durable stand. Holds my weighty Korg Sv-1 pretty well. Both levels are also pretty wide to accommodate different boards. Screws tighten clamps around the adjustable legs and rods so as to not damage them (unlike those screws that screw on a single point on the legs/rods and damage them).


Do be careful of the screws though, the knobs are made of plastic and may have some sharp edges - a simple sanding and trimming does the trick.

Also, it would be great if there are standard heights settings for the 2nd tier extension. Bottom tier has them but the top doesn’t. Takes a little more effort to get the top tier to level out. Should be an easy fix DIY-ing holes.

All in all a pretty great and sturdy stand for both stage and/or studio use. Definitely recommend!
Vakaus
Työnjälki
Käsittely
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
KM
Not good at all , get something else
Kamil M 13.12.2021
Someone really not clever designed this to be honest , 2 synths on it and with a little push the whole stand will tip over to the back , weigh distribution extremely poorly designed. Avoid!
Vakaus
Työnjälki
Käsittely
6
2
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
Upper tier on the wrong side? Backwards design?
Tuntematon 09.05.2022
It seems to me that this was messed up in the design phase. As several other reviewers have noted, the center of gravity is too far backwards, and the feet stick out way way too far in the front.
I fixed this by flipping the whole thing backwards and using it without the upper tier. Maybe I will try to modify it to install the upper tier flipped to the other side.
Vakaus
Työnjälki
Käsittely
3
1
Raportoi ongelmasta

Raportoi ongelmasta