A
Fantastic addition to the KM18813
Purchased this for the KM18813 arms that I bought as part of the KM18810 set. After setting up the stand and arms I set an Access Virus desktop sound module on top of the arms but given that the module is kind of small, it wasn't ideal. The KM18813 arms themselves weren't level and it was an awkward setup at best.
Getting the tray was well worth it. It's fairly sizable, allowing me to fit the above Virus module and a Kaossilator 3 Pro alongside it with plenty of room behind to spare. In the future I will likely swap out both units for another synthesizer or look to mix 'n' match different modules.
The KM18819 tray is made of steel and features a lip at the bottom end. Said lip contains a rubber fiber along it to prevent any modules from getting scratched or from damaging the lip itself. The back of the tray angles around the KM18813 arms to keep it firmly in place and there is a hole that makes it easy to handle wire management and for carrying the tray around if you intend on moving it frequently.
All in all, this is the perfect buy if you're looking to put smaller modules on top of the KM18813 arms. Plenty of room to work with and you could easily use it on top of desks or the likes if you just want a slightly angled workspace for your modules.
Pros: Durable, covered lip to prevent items from sliding off without damaging them, hole for easy carrying or for filtering wires through, plenty of space.
Cons: Could be a little longer, additional hole or two on each end would be useful for cable management.
Very happy with this purchase. Perfect for what I needed and would highly recommend if you're looking to use multiple modules together on top of the KM18813/KM18810.
Getting the tray was well worth it. It's fairly sizable, allowing me to fit the above Virus module and a Kaossilator 3 Pro alongside it with plenty of room behind to spare. In the future I will likely swap out both units for another synthesizer or look to mix 'n' match different modules.
The KM18819 tray is made of steel and features a lip at the bottom end. Said lip contains a rubber fiber along it to prevent any modules from getting scratched or from damaging the lip itself. The back of the tray angles around the KM18813 arms to keep it firmly in place and there is a hole that makes it easy to handle wire management and for carrying the tray around if you intend on moving it frequently.
All in all, this is the perfect buy if you're looking to put smaller modules on top of the KM18813 arms. Plenty of room to work with and you could easily use it on top of desks or the likes if you just want a slightly angled workspace for your modules.
Pros: Durable, covered lip to prevent items from sliding off without damaging them, hole for easy carrying or for filtering wires through, plenty of space.
Cons: Could be a little longer, additional hole or two on each end would be useful for cable management.
Very happy with this purchase. Perfect for what I needed and would highly recommend if you're looking to use multiple modules together on top of the KM18813/KM18810.
2
0
Zgłoś nadużycie
A
Wish it were a bit wider
You can get something like a TR-8S on there but if you want to have multiple devices the width is not quite enough. Also annoying that it only works with the K&M Omega stand due to the way it's bent underneath on the back side, making it impossible to just put on an upper tier of an X stand or so.
1
0
Zgłoś nadużycie
R
Worth every penny.
I have purchased three of these so far. I use two of them in a table top configuration to support my Gray Meanie over my OB-6 and my modular case over my Matriarch. The third is used to support my TD-3 and RD-6. They are great for supporting these types of modules and are very light weight and sturdy.
0
0
Zgłoś nadużycie
I
Must buy
A real good extra feature for K&M extension units.
Got enough room for laptop, effect pedals, drum machines and
smaller synths. Has rubber protection to prevent things to fall down and get scratched or damaged. Stays very stable on 3-rd or 2-nd stand.
Got enough room for laptop, effect pedals, drum machines and
smaller synths. Has rubber protection to prevent things to fall down and get scratched or damaged. Stays very stable on 3-rd or 2-nd stand.
0
0
Zgłoś nadużycie
C
Praktisches Tray
Dieses Tray ist ein nützlicher Zusatz zum K&M Aufsatz 18811. Ein wichtiger Hinweis: dieses Tray lässt sich nur mit dem Aufsatz 18811 benutzen, wenn die beiden Arme des Aufsatzes weit auseinander aufgestellt sind.
0
0
Zgłoś nadużycie
t
K&K Rocks
Great tray for a drum machine on top of keyboard. As always K&M quality is oustanding !
0
0
Zgłoś nadużycie
S
Good stand for kit
An ideal support for keyboards and other items on my stand.
0
1
Zgłoś nadużycie
A
Great idea well executed
I've done a full review for the main stand so just a short one here.
I've used this with the 18813 arms. The 18819 tray is very well made from a heavy duty sheet of metal. It connects positively with the arms and does not slide about. There is a cutout handle for carrying the tray and a material covered lip on the front edge to stop items rolling off. It is plenty big enough for a PC keyboard, mouse mat and mouse so can mean you can use the keyboard stand as a workstation for your DAW. The front lip is rounded off by the material so it is comfortable to rest your wrists on.
Highly recommended
I've used this with the 18813 arms. The 18819 tray is very well made from a heavy duty sheet of metal. It connects positively with the arms and does not slide about. There is a cutout handle for carrying the tray and a material covered lip on the front edge to stop items rolling off. It is plenty big enough for a PC keyboard, mouse mat and mouse so can mean you can use the keyboard stand as a workstation for your DAW. The front lip is rounded off by the material so it is comfortable to rest your wrists on.
Highly recommended
0
0
Zgłoś nadużycie
GG
Amazing
I really like K&M products It's like an armored tank 👍
0
0
Zgłoś nadużycie
G
Handy tray for K&M stand
I bought this tray to allow me to use smaller synth modules and drum machines on the upper part of the K&M stand that I bought.
Simple to install and very strong.
Simple to install and very strong.
0
0
Zgłoś nadużycie
